Zanussi ZGL640TX Manual de usuario

ZGL640 TGas hobInstructionbookletIEGB

10As soon as a liquid starts boiling, turn down theflame so that it will barely keep the liquidsimmering.Use only pans or pots with flat bottom.If you

11Before any maintenance or cleaning can be carried out, youmust DISCONNECT the hob from the electricity supply.The hob is best cleaned whilst it is s

12Something Not Working?If the hob is not working correctly, please carry out the following checksbefore contacting your local Service Force Centre.

13OVERALL DIMENSIONSOVERALL DIMENSIONSOVERALL DIMENSIONSOVERALL DIMENSIONSOVERALL DIMENSIONS Width: 580 mmDepth: 500 mmCUT OUT DIMENSIONSCUT OUT DIMEN

14BURNER RAPID SEMI-RAPID AUXILIARY(large) (medium) (small)POSITION MAX MIN MAX MIN MAX MINNOMINAL THERMAL 3.0 0.75 2.0 0.45 1.0 0.33POWER (kW)NOMINAL

15Important safety requirementsThis hob must be installed in accordance with the Gas Safety (Installation and Use)Regulations (Current Edition) and th

16A)A)A)A)A ) End of shaft with nutB)B)B)B)B ) WasherC)C)C)C)C ) ElbowInstallationIMPORIMPORIMPORIMPORIMPORTTTTTANTANTANTANTANTAny gas installation mu

17It is important to install the elbow corrIt is important to install the elbow corrIt is important to install the elbow corrIt is important to instal

182BBBBBuilding over a kitchen unituilding over a kitchen unituilding over a kitchen unituilding over a kitchen unituilding over a kitchen unitwith do

19Carry out the building in of the hob asfollows:• put the seals supplied with thehob, on the edges of the cut out,taking care that the seals meetwith

2Thank you for selecting our applianceThank you for selecting our applianceThank you for selecting our applianceThank you for selecting our applianceT

20Electrical ConnectionsAny electrical work required to install this hob should beAny electrical work required to install this hob should beAny electr

213) Connect the brown (live) wire to the terminal in the plug whichis marked with the letter 'L' or coloured red.Upon completion there must

22CommissioningWhen the hob has been fully installed it will be necessary to check theminimum flame setting. To do this, follow the procedure below.1)

23Conversion from Natural Gas to LPGIMPORTANTThe replacement/conversion from natural gas to LPG should only beundertaken by a competent person.It is i

24Guarantee/Customer ServiceStandard guarantee conditionsStandard guarantee conditionsStandard guarantee conditionsStandard guarantee conditionsStanda

25Service and Spare PartsService and Spare PartsService and Spare PartsService and Spare PartsService and Spare PartsIn the event of your appliance re

26This appliance is guaranteed by Electrolux in each of the countries listed at the backof this user manual, for the period specified in the appliance

27

39715-6801 02/10 R.Awww.zanussi.co.uk

3ContentsImportant Safety InformationImportant Safety InformationImportant Safety InformationImportant Safety InformationImportant Safety Information.

4Important Safety InformationYYYYYou MUST rou MUST rou MUST rou MUST rou MUST read these waread these waread these waread these waread these warnings

5lack of oxygen. When using the hob for a long period time, the ventilation should be improved,by opening a window or increasing the extractor speed.

6INSTALLATIONAny gas installation must be carried out by a registeredAny gas installation must be carried out by a registeredAny gas installation must

7Description of the Hob3213541. Auxiliary Burner2. Rapid Burner3. Semi-rapid Burners4. Control knobs5. Electric Ignition Push Button

8Lighting the burnersFor easier lighting, proceed before putting a pan on the pansupport.Once the hob has been installed, it is important to remove a

9Do not keep the control knob pressed for more than 15 seconds.If the burner does not light even after 15 seconds, release thecontrol knob, turn it t