Zanussi ZCG612J1XA Manual de usuario descargar pdf (Pagina 9)

A. Gas connection point (only one point is

applicable for the appliance)

B. Gasket

C. Adjustable connection

D. LPG pipe holder

HOB INJECTORS REPLACEMENT

Replace the injectors when you change the gas

type.

1. Remove the pan supports.

2. Remove the caps and crowns of the burner.

3. Remove the injectors with a socket spanner 7.

4. Replace injectors with the ones necessary for

the type of gas you use.

5. Replace the rating plate (it is near the gas

supply pipe) with the one for the new type of

gas supply.

You can find this plate in the bag

supplied with the appliance.

If the supply gas pressure is not constant or it is

different from the necessary pressure, install an

applicable pressure adjuster on the gas supply

pipe.

ADJUSTING THE MINIMUM GAS LEVEL ON

THE HOB BURNER

1. Disconnect the appliance from the electricity.

2. Remove the knob for the hob. If there is no

access to the bypass screw dismount the

control panel before adjustment start.

3. With a thin and flat screwdriver adjust the

bypass screw A.

The model determines the position of the

bypass screw A.

Changing from natural gas to liquid gas

1. Fully tighten the bypass screw.

2. Put the knob back.

Changing from liquid gas to natural gas

1. Unscrew approximately one turn the bypass

screw position A.

2. Put the knob for the hob back.

3. Connect the appliance to the electricity.

WARNING! Put the mains plug

into the mains socket only if all

parts are back into their initial

position. There is a risk of injury.

4. Light the burner.

Refer to "Hob - Daily use" chapter.

5. Turn the knob for the hob to the minimum

position.

6. Remove the knob for the hob again.

7. Screw on slowly the bypass screw till the flame

becomes minimum and stable.

8. Put the knob for the hob back on.

OVEN INJECTOR REPLACEMENT

1. Remove the bottom plate of the oven cavity A

to get access to the oven burner B.

2. Release the screw C, which keep the burner in

position.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 ... 27 28

Comentarios a estos manuales

Sin comentarios

Modelos	Tipo de documento
SeaTalk-SeaTalk ng	Especificaciones Raymarine SeaTalk-SeaTalk ng Specifications, 28 paginas
SmartPilot SPX-30	Manual de usuario SPX SmartPilot System Installasjon SPX 10, SPX 30, 54 paginas
ST1000+	Especificaciones Raymarine ST1000+ Specifications [en] , 8 paginas
ST1000 Plus	Especificaciones Raymarine ST1000 Plus Specifications, 76 paginas
ST2000+	Manual de usuario Installer et utiliser un pilote ST2000+ sur un First 30, 7 paginas
ST40	Especificaciones Raymarine ST40 Product specifications, 43 paginas Especificaciones Raymarine ST40 Product specifications, 53 paginas Manual de usuario ST40 BIDATA manuale, 56 paginas
ST50 plus	Especificaciones Raymarine ST50 plus Product specifications, 21 paginas Manual de usuario Distributed by Any reference to Raytheon or RTN in this, 18 paginas
ST60	Manual de instalación Raymarine ST60 Installation manual, 50 paginas Especificaciones Raymarine ST60 Specifications, 52 paginas Especificaciones Raymarine ST60 Specifications, 54 paginas
ST70	Guía de instalación Raymarine ST70 Installation guide [de] [en] [fr] , 26 paginas Guía de instalación Raymarine ST70 Installation guide, 48 paginas
ST70 Instrument	Manual de usuario Raymarine ST70 Instrument User manual, 12 paginas Guía de instalación Raymarine ST70 Instrument Installation guide, 28 paginas
ST80	Guía de instalación Raymarine ST80 Installation guide, 15 paginas

Zanussi ZCG612J1XA Manual de usuario Pagina 9

Comentarios a estos manuales

Raymarine No manuales de usuario

Zanussi ZCG612J1XA Manual de usuario Pagina 9

Comentarios a estos manuales

Relacionado con productos y manuales para Placas Zanussi ZCG612J1XA

Raymarine No manuales de usuario