Zanussi ZGG642C Manual de servicio Pagina 11
- Pagina / 16
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
11
Building In
Cut Out Size
The dimensions of the cut-out are given in the diagram.
550
470
55 min.
30
Rectangular cut-out size for hob
Dimensions are given in mm.
FO 2098
ON/OFF SWITCH
FLEX
OUTLET
ON/OFF SWITCH
FLEX
OUTLET
FO 0763
FO 0764
1
2
Dimensions are given in mm.
30
20 min
60
a
b
FO 1013
3
Building over a cupboard or
drawer
If the hob is to be installed above a cupboard or drawer
it will be necessary to fit a heat resistant board below
the base of the hob on the underside of the work
surface.
It is also recommended to carry out the electrical
connection to the hob as shown in diagrams 1 and 2.
Building over a kitchen unit
with door
Proper arrangements must be taken in designing the
furniture unit, in order to avoid any contact with the
bottom of the hob which can be heated when it is
operated. The recommended solution is shown in
diagram 3.
The panel fitted under the hob ("a") should be easily
removable to allow easy access if technical
assistance is needed. The space behind the kitchen
unit ("b") can be used for connections.
Fitting the hob to the
worktop
Before fitting the hob into the cut out, an adhesive
seal must be fitted to the underside outside edge
(Fig. 4) of the hob. It is essential that no gaps are left
in this seal in order to prevent spillage near the hob
seeping into the cabinet below.
1) Remove the pan supports, the burners caps
and crowns and turn the hob upside down,
taking care the ignition candles are not
damaged in this operation.
2) Place the sealing gasket all around the
glass top edge as shown in diagram 4.
3) Fit the hob in the cut out and push it down
until the glass top and the working top make
contact, as shown in diagram 5.
F
FO 2320
4
- GAS HOBS 1
- Important Safety Information 2
- Contents 3
- Description of the Hob 3
- Operation 4
- Maintenance and Cleaning 4
- Something Not Working? 5
- Service and Spare Parts 5
- Guarantee Conditions 6
- Customer Care Department 6
- ZANUSSI SERVICE FORCE 7
- Engineers technical data 9
- Important safety requirements 10
- Installation 10
- Building In 11
- Electrical connections 12
- Wiring Diagram 13
- Fault Finding 13
- Commissioning 15
- Grafiche MDM - Forlì 16
Relacionado con productos y manuales para Placas Zanussi ZGG642C
Placas Zanussi W ZCM Manual de servicio
(28 paginas)
(28 paginas)
Placas Zanussi ZGG-642 Manual de servicio
(20 paginas)
(20 paginas)
Placas Zanussi ZGG35214 Manual de usuario
(16 paginas)
(16 paginas)
Placas Zanussi ZVM 640 F Manual de usuario
(1 paginas)
(1 paginas)
Placas Zanussi ZGX65424XA Manual de usuario
(44 paginas)
(44 paginas)
Placas Zanussi ZGG35214XA Manual de usuario
(16 paginas)
(16 paginas)
Placas Zanussi ZCV662 Manual de usuario
(24 paginas)
(24 paginas)
Placas Zanussi ZGO75524BA Manual de usuario
(20 paginas)
(20 paginas)
Placas Zanussi 283580 Folleto
(2 paginas)
(2 paginas)
Placas Zanussi Gas Hob Manual de instrucciones
(16 paginas)
(16 paginas)
Placas Zanussi ZCM900X Manual de instrucciones
(28 paginas)
(28 paginas)
Placas Zanussi ZCM930X Manual de instrucciones
(32 paginas)
(32 paginas)
Placas Zanussi ZGS 682 ICT Manual de instrucciones
(36 paginas)
(36 paginas)
Placas Zanussi ZGF 782 Manual de instrucciones
(19 paginas)
(19 paginas)
Placas Zanussi ZCM 630 Manual de instrucciones
(28 paginas)
(28 paginas)
Placas Zanussi ZGF 643 Manual de usuario
(11 paginas)
(11 paginas)
Placas Zanussi ZGF 681 Manual de usuario
(12 paginas)
(12 paginas)
Placas Zanussi ZCM 611 Manual de instrucciones
(24 paginas)
(24 paginas)
Raymarine No manuales de usuario
Empezando en S
Comentarios a estos manuales