Zanussi ZKF641HW Manual de usuario Pagina 14

  • Descarga
  • Añadir a mis manuales
  • Imprimir
  • Pagina
    / 16
  • Tabla de contenidos
  • MARCADORES
  • Valorado. / 5. Basado en revisión del cliente
Vista de pagina 13
Electrical Connection
The mains connection must be carried out by an
expert electrician. The VDE-regulations and the
valid prescriptions by the local power supply boards
have to be compiled with.
Prior to connection it should be checked whether
the voltage stated on the type plate - i.e. the
nominal voltage of the appliance and of the
oven/control box is identical with the prevailing
mains voltage. The rating plate is located on the
hobs bottom.
The heating element voltage amounts to 230 V ~ .
The appliance will also perfectly perform with the
former mains voltage of 220 V ~ .
The mains connection must be carried out in a way
that a double-pole switch is used with a contact
opening of at least 3 mm, and disconnected by LS-
automatism, earth-leakage circuit-breaker or fuse.
A wire of type H05VV-F or of higher rating is to be
used as supply cable.
The mains terminal is located in the bottom of the
appliance behind a covering slide. It can be opened
with a screw driver (pic.).
According to the existing mains voltage, the
appliance must be connected in accordance with
the appropriate connections as shown. The bridges
of the terminal board are to be set in the marked
position.
The protective conductor is to be connected to
terminal . The protective conductor must be longer
than live leads.
The cable connections have to be established
as prescribed and the terminal screws be firmly
tightened.
Afterwards the supply cable has to be secured by
strain relief device and the covering slide must be
closed by firmly pressing down.
Prior to first use remove any existing labels and
protective foils from the ceramic glass plate or the
frame of the hob.
After connection to the power supply check each
cooking zone by briefly switching it the maximum
setting (10).
UK Only
Vista de pagina 13
1 2 ... 9 10 11 12 13 14 15 16

Comentarios a estos manuales

Sin comentarios

Raymarine No manuales de usuario

Empezando en S

Haga clic en el alfabeto a continuación para desplazarse a la lista completa de modelos que comienzan con esa letra

Modelos Tipo de documento
SeaTalk-SeaTalk ng
Especificaciones   Raymarine SeaTalk-SeaTalk ng Specifications, 28 paginas
SmartPilot SPX-30
Manual de usuario SPX SmartPilot System Installasjon SPX 10, SPX 30, 54 paginas
ST1000+
Especificaciones   Raymarine ST1000+ Specifications [en] , 8 paginas
ST1000 Plus
Especificaciones   Raymarine ST1000 Plus Specifications, 76 paginas
ST2000+
Manual de usuario   Installer et utiliser un pilote ST2000+ sur un First 30, 7 paginas
ST40
Especificaciones   Raymarine ST40 Product specifications, 43 paginas
Especificaciones   Raymarine ST40 Product specifications, 53 paginas
Manual de usuario   ST40 BIDATA manuale, 56 paginas
ST50 plus
Especificaciones   Raymarine ST50 plus Product specifications, 21 paginas
Manual de usuario   Distributed by Any reference to Raytheon or RTN in this, 18 paginas
ST60
Manual de instalación   Raymarine ST60 Installation manual, 50 paginas
Especificaciones   Raymarine ST60 Specifications, 52 paginas
Especificaciones   Raymarine ST60 Specifications, 54 paginas
ST70
Guía de instalación   Raymarine ST70 Installation guide [de] [en] [fr] , 26 paginas
Guía de instalación   Raymarine ST70 Installation guide, 48 paginas
ST70 Instrument
Manual de usuario   Raymarine ST70 Instrument User manual, 12 paginas
Guía de instalación   Raymarine ST70 Instrument Installation guide, 28 paginas
ST80
Guía de instalación   Raymarine ST80 Installation guide, 15 paginas